| From: |
"Dave Saville" <os2-wireless_users@2rosenthals.com> |
Full Headers
Undecoded message |
| Sender: |
os2-wireless_users-owner <os2-wireless_users-owner@2rosenthals.com> |
| Subject: |
[OS2Wireless] Login problems |
| Date: |
Thu, 19 May 2005 12:35:21 +0100 (BST) |
| To: |
"os2-wireless_users@2rosenthals.com" <os2-wireless_users@2rosenthals.com> |
|
|---|
On Thu, 19 May 2005 09:43:35 +0200 (CEST), Peter Verweij wrote:
>Hi,
>
>I use two nics on my T40 and it works great. Just a few things to remember.
>Each nic should be on its own networking address.
>I have the wireless on 192.168.1.18 and the wired on 192.168.3.19
>(important is not to have both on 192.168.1.x then the requester doesn't
>work).
>Next in ibmlan.ini both network adapters should be bound, search for net1
>and net2. But if you don't get an error during boot from network200a it
>should be oke.
>Next if change your wirelesscard ip-address it is sometime needed to stop
>the requester with:
>net stop req /y
>After a minute or so you can start up the requester again with
>net start req
>and then it should start. If you are to fast the requester startup quits
>with an error message.
>At the moment on a windows pc so I can't give you the exact errormessage.
Thanks for the replies so far but I think some of you are a bit confused as to
what I am trying to achieve. I am *not* trying to get both NICs to work at once
but boot and use either a cable connection to my LAN if I am in my office or a
WIFI connection if I am elsewhere such as the garden. So lets restate the
problem:
I can use my T21 either on cable or on wireless, or both at once provided they
are on two different subnets. However I cannot get the requester to start when
the box is booted and wifi activated.
In this scenario after boot neither NIC has an IP - both use DHCP. WIFI is not
active and there is no cable plugged in so the cable side is never going to do
anything. I start WIFI and it gets an IP. I can ping/telnet/ftp/whatever. I
then try a network login to get some mounted drives. The requester starts but
times out after several minutes with no helpful errors or log messages that I
can find.
The LAN NIC is bound to TCP/IP, NETBIOS and NETBIOS over TCP, the WIFI
initially was only bound to TCP/IP. I think I have both NETBIOS as I needed to
talk to old and new versions of winbloze without messing too much with the win
boxes.
In IBMLAN.INI there are NET1 & NET2, the first to TCPBEUI$,0 and the second to
NETBEUI$,1 - which I believe refer to adaptors 0 & 1 - which ties up with
protocol.ini
- Note that 0 & 1 are both the LAN NIC - because of the two NETBIOS protocols.
I tried adding the two NETBIOS settings to the WIFI adapter and guessed that
that might create NET3 & 4 - So I added them to IBMLAN.INI and to the
wkservices & srvnets. Then it would not start the requester even when on cable.
If I start on cable, start the requester and get my drives mounted then
shutdown the cable and start wifi the mounted drives still work.
Another question - If the mounted drives only appear when I log into the LAN
why don't they disappear when I logout?
--
Regards
Dave Saville
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
To unsubscribe from this list, send a message to
steward@2rosenthals.com with the command
"unsubscribe os2-wireless_users" in the body
(omit the quotes).
For help with other commands, send a message
to steward@2rosenthals.com with the command
"help" in the body (omit the quotes).
This list is hosted by Rosenthal & Rosenthal
P.O. Box 281, Deer Park, NY 11729-0281. Non-
electronic communications related to content
contained in these messages should be directed
to the above address. (CAN-SPAM Act of 2003)
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
|